Unwrap the ribbon and separate the ribbon roll from the bare core. Technical Reference, Specifications 6. Interface Specifications This section presents the interface specifications of IO ports for the printer. Do not touch print head surface by bare hands or with any hard equipment. Printer Maintenance Vertical streaks in the printout usually indicate a dirty or faulty print head. The viewing direction is facing the machine, and using hex socket screw driver for the adjustment. Dispenser Installation Install a dispenser into the printer as follows:
|Date Added:||12 April 2011|
|File Size:||15.59 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
To enable Peeling function, set by the LCD panel.
It is to control cut Phillips screwdriver actions of guillotine cutter. Page 17 Switching Ribbon Wound Ink-side in or Ink-side out X-0100vl printer is produced to suit flexible applications, no matter with ribbon wound ink-side in manufacturing defaultor with argox x-1000vl wound ink-side out. Argox x-1000vl Operation, Front Panel Overview 2.
If the test print appears as Figure A, remain the screw at the right of Ribbon Argod fixed, then loose the screw at the left, and gradually fine-tune upward, until the print quality gets improved. The printer will then feed the labels through the cutter automatically. Switching Argox x-1000vl Wound Ink-side in or Ink-side out The printer is produced to suit flexible applications, no matter with ribbon wound ink-side in manufacturing defaultor with ribbon wound ink-side out.
Water or spit should be kept away in case of corrosion on heating elements. After the related files argox x-1000vl been copied to your argox x-1000vl, click “Finish”. Page 58 Seagull driver is to run the DriverWizard utility from the Installation Argox x-1000vl where the Seagull driver files locates.
Argox XVL, DPI Industrial Barcode Printers
argox x-1000vl Enter Printer name i. For the XVL, ignore this step. Please contact your local Argox argox x-1000vl if you need this cable. Then install the ribbon: Push aggox the peel-off mechanism release lever and lead the media under the peeler module. Check all the data on the showing screen, if it is correct, click “Finish”.
ARGOX XVL USER MANUAL Pdf Download.
Centronics allows a much higher communication speed than serial. Windows XP; steps in other versions of argox x-1000vl systems are similar.
LCD Function Setting Procedure The following x-1000v, is an example of setting procedure to direct thermal printing mode: W mm x H mm x D mm. Connect the Parallel cable, Zrgox cable, or Ethernet cable to the proper port argox x-1000vl the printer and on your computer. Adjust Position Of Label Sensor Adjust Position of Label Sensor Function of the label sensor is to detect argox x-1000vl gap, notch, or holes of labels, to help the argox x-1000vl for accurate print positions and label length.
Turn off the printer; disconnect the AC power cable.
Ribbon Tension Adjustment The default setting when shipped from Argox factory is shown as Argox x-1000vl 2 — the two arrows are argox x-1000vl line with the black line. Figure 3 Dispenser Module Peel Lever Refer to the following examples. Parallel centronics Parallel X-11000vl The parallel port is a standard pin Centronics connector. Open the top cover of the printer to see if the media compartments are in order.
Comments to this Manuals Your Name. Transmission Problems, Recovery graphics or forms. Argox x-1000vl Centronics The parallel port is a standard pin Centronics connector.
The LCD displays this message: Do not operate the printer in an area where it might get wet. Turn off the printer. Install the ribbon and media. Page 79 Figure Argox x-1000vl off the printer before cleaning.